| Info |
|---|
The document describes how to configure Push-to-talk feature for x-hoppers broadcast on mobile. Download mobile app: Created: June 2024 Updated: December 2024 Permalink: https://x-hoppers.atlassian.net/wiki/x/AYAx |
| Table of Contents | ||
|---|---|---|
|
Introduction
The feature allows you to send Push-to-talk messages to x-hoppers broadcast from x-bees conversationa group conversation on mobile. With this option, users can send voice messages to x-hoppers broadcast via mobile and receive broadcast messages to x-bees conversation conversations on mobile, having them played automatically in Speaker mode.
Requirements
x-hoppers system on WMS 6.07 or higher
x-hoppers-SalesFloorHopper licence or higher
WMS v. 6.07
x-bees mobile app v. recordings”
Mobile app 1.68 or and higher
Configuration
Add the parameter --conf_recording or -ptt cr to the /etc/systemd/system/pbx-data-engine.service.d/override.conf file.
Example:
Code Block vi /etc/systemd/system/pbx-data-engine.service.d/override.conf [Service] ExecStart= ExecStart=/usr/sbin/pbx_data_engine.py --conf_recordingdaemon --daemoncr
Restart the service to apply the changes:
Code Block systemctl daemon-reload systemctl restart pbx-data-engineFor the feature to work on mobile, make sure there is an included procedure pbxservicepbxservices (Services codes dialplan) set in Dialplan:
...
Create a conversation in x-bees, adding all members of x-hoppers broadcast, including all W-AIR headset users and all users of x-bees mobile app, that are going to use the Push-to-talk feature. The transcription and audio files of what was pronounced in x-hoppers broadcast will be added to this conversation.
Add the following lines to the /rw2/etc/pbx/x-hoppers.json file:
Code Block [ { "audio_conf_id": 0, "xbees_channel_id": "a1b88b80-a287-4848-8d1a-9fb8721f" } ]Where:
“0” is the ID number of x-hopper conferencebroadcast
"a1b88b80-a287-4848-8d1a-9fb8721f" is the ID of x-bees conversation.
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
| Tip | ||||||
Note: The conversation ID is available in the conversation URL:  |
Restart the service to apply the changes:
Code Block systemctl daemon-reload systemctl restart pbx-data-engine
Usage on Mobile
...
Usage
To start using this feature:
Go to mobile app Settings -> Integrations -> enable the toggle next to Allow Push-to-talk option:
...
| Panel | |
|---|---|
| panelIconId | atlassian-note |
| panelIcon | :note: | bgColor | #E3FCEF
| Tip | |
Note: The Push-to-Talk button under Allow Push-to-Talk can currently be used to connect Jabra Perform 45 headset. |
| Note |
|---|
Important: On Android, it is necessary to allow "Nearby Devices" permission for x-bees the mobile app for the Push-to-talk feature to work. |
...
To send a voice message to x-hoppers broadcast via mobile, user should press and hold the Push-to-talk button next to the message field:
...
| Note |
|---|
Current limitation: PTT messages should not be longer than 3 minutes in case of x-hoppers broadcast with transcription of in-store conversations enabled. |
The message is played to users in x-hoppers broadcast. Also, once mobile user enters the x-hoppers conversation, the group messages are automatically played on mobile in Speaker mode.
What is pronounced in x-hoppers broadcast is added as a message from the relevant user with a transcription and audio file:
...
To exit the broadcast, go to the Inbox tab -> press > press and hold the relevant conversation -> on the pop-up screen that appears below, press the option Exit x-hoppers group:
...